Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

BMX

Odyssey Gyro G3 Detangler Upper Top Plate
$2.50
The Gyro G3 upper top plate is designed for use with the G3 detangler.
Odyssey Cable Knarps
$3.99
- Sold in pairs - Allen wrench included
Odyssey Par Ends
$3.99
Odyssey's custom-designed Par Ends come standard with all of their grips. Its special plastic composite will not shatter like cheap bar ends do, and they’re very lightweight. The Par End is a combination of the over-the-bar-style cap and the inside-the-bar-style to prevent the inner portion from blowing out like it does on ordinary press-fit bar ends. Comes stock on all of Odyssey's grips.
Odyssey High Pressure Rim Strips
$4.99
When you can’t even see a part, you might forget about it, but it doesn’t mean its not important. Flat tires are probably the most common bicycle failures. Many times, flats are caused by the rims, specifically the lack of protection from the rims' sharp edges. Good rim strips didn’t exist for BMX rims. They work well and improve the function of any 20 inch rim. If you forget about them, that means they are doing their job.
Stolen Thermalite Bar Plugz
$4.99
Unique design with Thermalite for durability. In-moldED Steel insert to eliminate bar punch through. Expands securely with a grub screw to fit tightly on regular, 9, 11, & 13 butt bars. - Expands securely with a grub screw to fit tight - Material: Thermalite - Weight: 1.0-ounces per pair
Stolen Thermalite Peg
$5.99
Made of Stolen's proprietary Thermalite material, the sleeve resists cracking and deformation while sliding better than chromoly on most surfaces. These sleeves come stock on the Stolen Silencer & Fiction Troop pegs and will also fit over our chromoly Barrel Peg (with axle washer). - Length: 4.4-inch - Diameter: 1.6-inch - Material: Plastic (Thermalite) - Weight: 0.8- ounce each - Replacement sleeve only - Sold individually
Odyssey Gyro G3 Lower Cables
$7.99
- Lower cables for Odyssey's Gyro G3 (sold separately). - Universal fit. - Lower cables only.
Odyssey Ghost Brake Pads
$8.50
One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable too. The Ghost Pad addresses the hassles of brake pad installation by eliminating the traditional dome shaped washers used for toe-in. The pad improves stiffness by building the toe-in into the pad shape and utilizing a solid extruded aluminum frame at its core. The Ghost Pad’s assembly consists of simply lining it up with the rim and tightening down an M6 female bolt. Comes stock on the Springfield brake. SPECS Hardware: - In-bound bolt, 5mm Hex Key, M6x1.0 Thread - Pad Material: Black (standard) or Clear Rubber (Soft) - Weight: 1.0oz / 28g (pair)
GSport G.L.A.N.D. MK IV Hub Guards
$9.99
The MK 4 version continues the GLAND’s heritage, but in a smaller and sleeker overall size which should appease many riders. The images beside show the top, profile, and under side of each guard.
Sunday Cornerstone Grips
$9.99
Sunday's Cornerstone Grips rock traditional styling, current branding, and come in at 150mm in length with plenty of color options. It's not a bad idea to keep an extra pair around.
WeThePeople Arrow 115 Grips
$9.99
WeThePeople's Arrow 115 Grips have the perfect texture and density to give you new confidence while railing it on the bike. Material: VEX rubber compound Rubber durometer: 30° Size: 115mm x 28mm Specials: soft angled rib design with medium-sized flange; includes WeThePeople nylon barends
WeThePeople Arrow 146 Grips
$9.99
WeThePeople's Arrow 146 Grips have the perfect texture and density to give you newfound confidence while railing it on the bike. Material: VEX rubber compound Size: 146mm x 28mm Specials: soft angled rib design with medium-sized flange; includes WeThePeople nylon barends
Black Ops Knurled Pro
$12.39
- Threads onto 3/8" axles - Double-sided - Oversized - Alloy - Length: 3" / 74mm - Width: .94" / 24mm - Sold as a pair
Odyssey Adjustable Quik Slic Kable
$13.99
As the name implies, this new version can be easily adjusted to cover 3 different lengths by utilizing the cable’s unique straddle interface connection. This tool-free feature allows the Adjustable Quik Slic Kable to be a one-size-fits-all cable for virtually every braking configuration. FEATURES - Adjustable hanger slot allows upper cable to rotate for optimum alignment. - The integrated hanger and straddle cable creates direct routing to brake arms with no bends or twists to reduce flex. - Linear K-Shield mesh housing offers higher compression rate and lighter weight than standard steel mesh. - All Odyssey Linear cables are offered with the K-Shield housing. - Specially designed and machined Volcano ferrules prevent premature housing blowout. Velcro strap included. SPECS - Housing length: 995mm - Frame requirements: Slotted cable stop and guides. 245mm (+/-3) distance from center brake boss to the front of the cable stop is recommended. - Brake requirements: Open-ended U-brake arms. - Works with most brake levers. - Velcro strap included.
Black Ops Lead Foot
$14.39
- Steel - Threads onto 3/8" axle - Knurled & grooved - Diameter: 33mm - Sold in pairs
GSport Uniguard Hub Guard
$14.99
The new Gsport Uniguard is a simple, inexpensive functional guard that eliminates the need to spread the dropouts. It’s made from Heat-Treated Cr-Mo Steel and is LHD and RHD compatible as well as Drive and Non-Drive compatible. All bases covered. Available in 14mm or 3/8?.
Odyssey Race Linear Kable
$14.99
Odyssey took their proven Linear Slic Kable housing and replaced the steel linear wire with aluminum. Utilizing the aluminum wire in the housing saves you significant weight, roughly 30%. This cable also features their specially designed “volcano” ferrules that they’ve used since 2008 to prevent housing blowouts. This Kable also comes with color-coaded inner wires and ball ends to differentiate between their regular Linear’s Race Linear Slic Kable. - Length: 60 – 65mm - Black
WeThePeople Supreme Seat Clamp, 25.4mm
$14.99
WeThePeople's Supreme Seat Clamp is great for adding a little bit of bling to your ride. This clamp is CNC machined from lightweigh 6061 aluminum and it works with standard BMX 25.4mm seatposts.
Black Ops CT 2.0 Chain Tensioner
$16.99
- CNC machined 6061-T6 aluminum chain tensioners - Compatible with 3/8 inch and 10mm axles - Single bolt operation makes tensioning a simple task - Material: 6061AL
Odyssey Graduate Peg
$18.99
This plastic peg features a full 4130 core with a long-lasting, fast-sliding, plastic sleeve. - 1.5-inch outer diameter - 14mm with 3/8-inch adapter - Sold individually - Weight: 7.6oz - Replacement sleeves sold separately
Odyssey Mid Bottom Bracket
$18.99 - $24.99
- Made to fit crank spindles and press-fit Mid BB frames. - Simple and easy to install. - Includes an assortment of spacers to optimize chainline and crank clearance. - Odyssey 6061-T6 aluminum dust spacer included.
Odyssey HGS Spokes
$19.99
- Straight gauge spokes with a proprietary grade of stainless steel that is as good or better than the materials used by the world’s most renowned spoke makers. - Sized and dimensioned specifically for BMX.
Odyssey Clutch Hub Guard
$22.99
- Press fit designed to work the hub's non-drive side collar.
Black Ops Chain Tensioner
$24.59
- Forged alloy construction - Double bolt centering design - Oversize 6mm hex bolts
Odyssey M2 Monolever
$24.99
The M2 lever works with a single cable or Odyssey’s patented dual cable system. The M2 cable system improves braking power for GYRO users. - Right hand only (works flipped on the left) - M2 specific upper cable and single cable coupler included.
Odyssey Pro Headset (Conical)
$24.99
New dust cap design, with Monogram laser etched logo, for a cleaner look to accommodate a taller riding set up with less spacers. Same quality as Odyssey's Pro Headset using high-quality sealed bearings and a precision tapered wedge to keep the headset tight at all times. FEATURES - High-quality sealed bearings. - Color matched spacers included. - 15mm dust cap. With 3mm, and 2mm spacers - Laser etched Odyssey bearings. SPECS - Campagnolo standard spec. - 1 1/8-inch integrated headset. - 45º tapered bearings - 41.8mm outer diameter (fits 42mm BMX head tubes).
Odyssey Quartet Hub Guard
$24.99
Designed specifically for use with Odyssey's Quartet FRONT or REAR hubs. SPECS - Forged from 7075-T6 aluminum for greater strength and durability - Steel insert prevents guard deformation, prolonging bearing life
Black Ops GL Pegs
$25.59
- Super hardened nylon construction - 40mm diameter, 100mm length - Special insert fits 3/8" or 14mm axles - 90g (pair)
Odyssey Tom Dugan Tires
$25.99
Tom likes to ride fast and go very high. These tires were designed to help him do just that. With a fast center tread, these tires are made for park, street and even dirt too. The side profile is reminiscent of a motorcycle tire as well, which is a nod to Tom’s motorcycle lovin’ ways.
Odyssey Tripod Post
$25.99
Odyssey is proud to offer their new tripod post. It allows for the two most popular seat angles amongst riders and it’s clean, light and easy to install. SPECS - 25.4mm diameter - 6061-T6 Aluminium, CNC machined
Page 1 of 2 Next page